Arduino Radio Control  Arduino Radio Control
http://www.reseau.org/arduinorc

HomePage

.

ChangeLog

Main.ChangeLog History

Hide minor edits - Show changes to output

June 08, 2014, at 05:01 PM by 78.248.132.152 -
Changed line 3 from:
June 2, 2014 Version 1.5.5
to:
June 8, 2014 Version 1.5.5
June 08, 2014, at 04:34 PM by 78.248.132.152 -
Changed line 10 from:
*Changed endpoints computation: now EPL,EPH variables define end point position in % from the center: '''you must change your endpoints settings accordingly'''
to:
*Changed endpoints computation: now EPL,EPH variables define end point position in % from the center: '''you must update your endpoints settings accordingly'''
June 08, 2014, at 01:45 PM by 78.248.132.152 -
Changed line 7 from:
*New command [[Cmd.ViewBat|PRINT VOLT]] to display battery voltage
to:
*New command [[Cmd.ViewBat|PRINT VOLT]] to display the battery voltage
June 08, 2014, at 01:44 PM by 78.248.132.152 -
Changed line 7 from:
*New command PRINT VOLT to display battery voltage
to:
*New command [[Cmd.ViewBat|PRINT VOLT]] to display battery voltage
June 08, 2014, at 01:09 PM by 78.248.132.152 -
Changed line 8 from:
*New ways to switch models on the field: stepping through all models with a push button, or direct model selection with a rotary switch
to:
*New ways to switch models on the field: stepping through all models with a push button, or direct model selection with a [[Projects.RotSwich|rotary switch]]
June 08, 2014, at 08:54 AM by 78.248.132.152 -
Changed line 6 from:
*Changed command mode's serial speed to 2400 bps to prevent Arduino's serial buffer overflow when uploading settings: '''you must change your Serial Monitor speed accordingly'''
to:
*Changed command mode's serial speed to 2400 bps to prevent Arduino's serial buffer overflow when uploading models: '''you must change your Serial Monitor speed accordingly'''
June 08, 2014, at 08:53 AM by 78.248.132.152 -
Changed line 6 from:
*Changed command mode's serial speed to 2400 bps to prevent Arduino's serial buffer overflow when uploading: '''you must change your Serial Monitor speed accordingly'''
to:
*Changed command mode's serial speed to 2400 bps to prevent Arduino's serial buffer overflow when uploading settings: '''you must change your Serial Monitor speed accordingly'''
June 08, 2014, at 08:53 AM by 78.248.132.152 -
Changed lines 5-6 from:
*Moved all user-customizable settings into new file arduinotx_config.h to facilitate software customization. Edit this file as needed. Normally, you do not have to make changes to any other file.
*Changed command mode's serial speed to 2400 bps to prevent Arduino's serial buffer overflow when uploading with txupload: '''you must change your Serial Monitor speed accordingly'''
to:
*Moved all user-customizable settings into new file arduinotx_config.h to facilitate software customization. Edit this file as needed. Normally, you won't have to make changes to any other file.
*Changed command mode's serial speed to 2400 bps to prevent Arduino's serial buffer overflow when uploading: '''you must change your Serial Monitor speed accordingly'''
June 08, 2014, at 08:51 AM by 78.248.132.152 -
Added lines 5-6:
*Moved all user-customizable settings into new file arduinotx_config.h to facilitate software customization. Edit this file as needed. Normally, you do not have to make changes to any other file.
*Changed command mode's serial speed to 2400 bps to prevent Arduino's serial buffer overflow when uploading with txupload: '''you must change your Serial Monitor speed accordingly'''
Deleted lines 10-11:
*Changed command mode's serial speed to 2400 bps to prevent Arduino's serial buffer overflow when uploading with txupload: '''you must change your Serial Monitor speed accordingly'''
June 08, 2014, at 08:43 AM by 78.248.132.152 -
Changed line 7 from:
*New option: full curve exponential may apply to the throttle channel (for gas engines)
to:
*New option: full curve exponential may now apply to the throttle channel (for gas engines)
June 08, 2014, at 08:40 AM by 78.248.132.152 -
Added lines 2-10:

June 2, 2014 Version 1.5.5
*''This version uses the same EEPROM layout as before so your models settings will be preserved after uploading it into your transmitter''
*New command PRINT VOLT to display battery voltage
*New ways to switch models on the field: stepping through all models with a push button, or direct model selection with a rotary switch
*New option: full curve exponential may apply to the throttle channel (for gas engines)
*Changed endpoints computation: now EPL,EPH variables define end point position in % from the center: '''you must change your endpoints settings accordingly'''
*Changed command mode's serial speed to 2400 bps to prevent Arduino's serial buffer overflow when uploading with txupload: '''you must change your Serial Monitor speed accordingly'''

Changed line 6 from:
*Added a Piezzo buzzer to sound alarms
to:
*Added a piezzo buzzer to sound alarms
Changed lines 4-6 from:
*Transmitter battery low voltage alarm
*New BAT variable added to Global variables group to set battery level alarm
*Piezzo buzzer
to:
*New feature: transmitter battery monitoring
*New BAT variable added to Global variables group to set battery low voltage alarm
*Added a Piezzo buzzer to sound alarms
Added lines 2-7:

September 12, 2013 Version 1.4.0
*Transmitter battery low voltage alarm
*New BAT variable added to Global variables group to set battery level alarm
*Piezzo buzzer
*Fixed underflow in subtrim computation, this issue existed in v1.3 for negative values of CHAN_SUB < -10%
July 06, 2013, at 01:27 PM by 78.248.132.152 -
Changed line 9 from:
*ESC key cancels input in Command mode
to:
*ESC key cancels input in Command mode when connected with ''putty'' or ''screen''
July 06, 2013, at 01:05 PM by 78.248.132.152 -
Changed line 3 from:
July 14, 2013 Version 1.3
to:
July 6, 2013 Version 1.3.0
July 05, 2013, at 08:21 AM by 78.248.132.152 -
Added line 13:
*Moved most constant strings and arrays to PROGMEM
July 05, 2013, at 08:18 AM by 78.248.132.152 -
Added line 13:
*Renamed *.ino files as *.cpp except the main sketch arduinotx.ino
July 05, 2013, at 07:23 AM by 78.248.132.152 -
Changed line 4 from:
*Exponential setting for each channel
to:
*New EXP variable defines exponential setting for each channel
July 05, 2013, at 07:22 AM by 78.248.132.152 -
Added line 10:
*Comments start by '#' instead of ';' in Command mode
Deleted line 12:
*Comments start by '#' instead of ';' in Command mode
July 05, 2013, at 07:21 AM by 78.248.132.152 -
Added lines 2-13:

July 14, 2013 Version 1.3
*Exponential setting for each channel
*Dual rate or Exponential do not apply to the throttle channel
*Added Model variables group
*Moved THC variable (Throttle channel number) to Model variables group
*New NAM variable (Model name) added to Model variables group
*ESC key cancels input in Command mode
*Improved alarms management
*Fixed bug in Model switching
*Comments start by '#' instead of ';' in Command mode
*txupload: added optional argument to resume upload at any line number
 
Page last modified on June 08, 2014, at 05:01 PM